Product Categories

Ethernet + 2-Port Serial (RS232/422/485) to Framed E1 Converter (Multi-Service Multiplexer)

Overview

The Ethernet + 2-Port Serial (RS232/422/485) to Framed E1 Converter (Model: KDS-E1F1R2) is a high-performance, large-scale FPGA-based multi-service protocol converter and self-learning Ethernet bridge engineered to multiplex one 10/100Base-T Fast Ethernet port and two asynchronous serial ports (RS232, RS422, RS485, or TTL optional) over a single framed E1 circuit. By leveraging existing PDH, SDH, or microwave E1 infrastructures, it provides a cost-effective integrated transport gateway for simultaneous LAN extension and industrial serial telemetry.

Featuring arbitrary N × 64 Kbps timeslot allocation (64 Kbps to 2,048 Kbps), non-intrusive OAM overhead management, SNMP network management support, 6 kV surge protection on serial interfaces, and built-in diagnostic loopback capabilities, the KDS-E1F1R2 streamlines commissioning and ensures carrier-grade operational reliability.

Features

  • Proprietary IC / FPGA Architecture: Engineered on a self-developed, proprietary IC/FPGA core for high integration, low latency, and long-term operational stability.
  • Non-Intrusive Remote OAM Management: Supports remote device monitoring and control via dedicated OAM management channels without occupying user payload timeslots, preserving full E1 bandwidth.
  • Flexible Framed E1 Timeslot Allocation (64K–2048K): Supports arbitrary timeslot selection on the framed E1 interface with configurable payload rates from 64 Kbps to 2,048 Kbps.
  • Master/Slave Rate Synchronization: Allows the local device to force the remote unit’s operating rate to synchronize automatically with the local configuration.
  • Remote Power-Off & E1 Fault Alarms: Provides dedicated LED alarm indicators for remote unit power failure, E1 line disconnection, and Loss of Signal (LOS).
  • Automatic E1 Loopback Protection: Features automatic E1 interface loopback detection to prevent converter lockups or crashes caused by accidental line loops.
  • Jumbo Frame Support (Up to 2,036 Bytes): Ethernet interface supports jumbo frames up to 2,036 bytes for transparent VLAN and MPLS packet transport.
  • Dynamic MAC Address Table & Frame Filtering: Features a built-in dynamic Ethernet MAC address table (4,096 entries) with local data frame filtering.
  • Auto-Negotiation & IEEE 802.1Q VLAN Support: Ethernet port supports 10/100 Mbps auto-negotiation, full/half-duplex operation, and IEEE 802.1Q VLAN tagging.
  • Auto-MDIX Cable Adaptation: Ethernet interface supports Auto-MDIX for automatic straight-through and crossover cable adaptation.
  • Ethernet Watchdog Self-Reset: Incorporates an automated Ethernet monitor self-reset mechanism to prevent system hang-ups and ensure continuous uptime.
  • Dual Clock Synchronization Modes: Provides two selectable timing modes: internal master clock and E1 line recovered clock.
  • Dual E1 Impedance Options: Supports both 75 Ω unbalanced coaxial and 120 Ω balanced twisted-pair E1 interfaces.
  • SNMP Network Management: Supports standard SNMP network management for centralized remote monitoring and configuration.
  • Multi-Standard Serial Interface Options: Provides two serial channels configurable as RS232, RS422, RS485, or TTL (optional).
  • Wide Asynchronous Baud Rate Range (300 bps–19,200 bps): Serial channels support adaptive asynchronous data transmission across baud rates from 300 bps to 19,200 bps.
  • ITU-T R.111 Serial Multiplexing: Serial data multiplexing over E1 complies with ITU-T R.111 transition-encoding (jumping coding) standards.
  • Non-Destructive Remote RS232 Loopback Testing: Local RS232 port can command the far-end RS232 port to loop data back to the local end (outer-ring loopback), allowing safe verification of the RS232 transceiver chip without hardware damage.
  • 6 kV Surge Protection on Serial Ports: Serial interfaces meet IEC 61000-4-5 (8/20 μs) surge protection standards up to 6 kV Differential Mode (2 Ω impedance) and 6 kV Common Mode (2 Ω impedance).

Parameters

◆ E1 Interface (Framed)

Interface & Framing Standards Compliant with ITU-T G.703 and G.704 (Arbitrary timeslot allocation: 64 Kbps to 2,048 Kbps)
Interface Rate N × 64 Kbps ± 50 ppm (N = 1 to 32)
Line Code HDB3
Impedance Options 75 Ω (unbalanced coaxial) / 120 Ω (balanced twisted-pair)
Jitter Tolerance Compliant with ITU-T G.742 and G.823 recommendations
Allowed Input Attenuation 0 to -6 dBm

◆ Ethernet Interface (10/100M)

Interface Rate 10/100 Mbps adaptive, full/half-duplex auto-negotiation
Protocols & Standards Compatible with IEEE 802.3, IEEE 802.1Q (VLAN); Jumbo frames up to 2,036 Bytes
MAC Address Table Capacity 4,096 MAC address entries with dynamic learning and local frame filtering
Physical Connector 1 × RJ45 electrical port supporting Auto-MDIX

◆ Serial Interfaces (2 × RS232 / RS422 / RS485 / TTL)

Supported Standards EIA/TIA-232 / RS-232 (ITU-T V.28); EIA/TIA-422 / RS-422 (ITU-T V.11); EIA/TIA-485 / RS-485 (ISO/IEC 8284); TTL (optional)
Baud Rate & Multiplexing 300 bps to 19,200 bps adaptive asynchronous; ITU-T R.111 transition encoding over E1
RS-232 Pinout Signals RXD, TXD, Signal Ground (GND)
RS-422 Pinout Signals TXD+, TXD-, RXD+, RXD-, Signal Ground (GND)
RS-485 (4-Wire) Pinout Signals TXD+, TXD-, RXD+, RXD-, Signal Ground (GND)
RS-485 (2-Wire) Pinout Signals Data+ (TXD+), Data- (TXD-), Signal Ground (GND)
Surge Protection IEC 61000-4-5 (8/20 μs): Differential Mode 6 kV (2 Ω), Common Mode 6 kV (2 Ω)

◆ Working Environment

Operating Temperature -10°C to +50°C
Operating Humidity 5% to 95% (Non-condensing)
Storage Temperature -40°C to +80°C
Storage Humidity 5% to 95% (Non-condensing)

Specifications

Model Number KDS-E1F1R2
Product Name Ethernet + 2-Port Serial (RS232/422/485) to Framed E1 Converter (Multi-Service Multiplexer)
Functional Description 1-channel Framed E1 to 1 × 10/100Base-T Fast Ethernet + 2 × Asynchronous Serial (RS232/422/485/TTL) multi-service protocol converter with E1 loopback detection and SNMP support
Port Configuration 1 × Framed E1 interface (75 Ω / 120 Ω), 1 × 10/100Base-T Fast Ethernet RJ45 interface, 2 × Serial interfaces (RS232/422/485/TTL)
Power Input & Consumption Power Supply Options: AC 180V–260V / DC -48V / DC +24V  |  Power Consumption: ≤ 10W
Chassis & Dimensions Desktop Mini Chassis: 216 mm × 140 mm × 31 mm (W × D × H), 1.3 kg / pc  |  19-inch 1U Rackmount Chassis: 483 mm × 138 mm × 44 mm (W × D × H), 2.0 kg / pc

Application

Interested in this product? Submit your inquiry below for a prompt response.

Scroll to Top