Product Categories

4-Port Fast Ethernet to 16-Port E1 Convergent Network Bridge (Point-to-Multipoint Hub)

Overview

The 4-Port Fast Ethernet to 16-Port E1 Convergent Network Bridge (Model: KDS-E16) is a high-density 1U rackmount central-site aggregation gateway engineered for point-to-multipoint Ethernet-over-E1 transport. It aggregates up to 16 independent E1 branches—supporting both multi-E1 bundled convergence and up to 16 separate remote single-E1 Ethernet protocol converters—into a 4-port 10/100Base-TX Fast Ethernet switching hub with elastic bandwidth allocation from 64 Kbps to 2,048 Kbps per E1.

Built for telecom carriers, utilities, and private enterprise networks, the KDS-E16 features non-intrusive remote OAM management, WEB/SNMP/CLI administration, online firmware upgrades, loop-storm prevention, power-off vs. line-cut fault differentiation, and modular dual-power hot-backup redundancy.

Features

  • 16-Direction Point-to-Multipoint Aggregation: Aggregates traffic from up to 16 independent E1 directions at the central office, with each direction supporting a remote single-E1 protocol converter or multi-E1 bundled link.
  • Non-Intrusive Remote OAM Management: Monitors and manages remote terminal units over dedicated management channels without consuming user payload timeslots.
  • Flexible Timeslot & Framing Configuration (64K–2048K): Each E1 circuit supports arbitrary timeslot allocation with adjustable rates from 64 Kbps to 2,048 Kbps, plus selectable framed or unframed E1 operation synchronized with remote units.
  • Intelligent E1 Loopback Detection & Broadcast Storm Prevention: Detects accidental E1 line loopbacks and suppresses forwarding packets with identical source and destination MAC addresses to the Ethernet switch ports, preventing switch crashes.
  • Remote Power-Off vs. E1 Line-Break Fault Discrimination: Accurately distinguishes whether an E1 Loss of Signal (LOS) is caused by a remote device power outage or a mid-span transmission line disconnection.
  • Jumbo Frame Support (Up to 2,036 Bytes): Ethernet ports support extended frame lengths up to 2,036 bytes.
  • 4-Port Fast Ethernet Switching & VLAN Support: Provides four 10/100Base-TX Ethernet ports in switching mode with full/half-duplex auto-negotiation, IEEE 802.1Q VLAN support, and Auto-MDIX crossover/straight-through cable adaptation.
  • Ethernet Data Watchdog Self-Reset: Built-in automated Ethernet data monitoring and self-reset circuitry ensures continuous operation without system lockups.
  • Independent Per-Direction Clock Selection: Each E1 direction supports two selectable timing modes: internal E1 master clock and E1 line recovered slave clock.
  • Dual E1 Impedance Options: Supports both 120 Ω balanced twisted-pair and 75 Ω unbalanced coaxial E1 interfaces.
  • Multi-Protocol Management (SNMP / WEB / CLI): Equipped with a dedicated SNMP network management interface on the rackmount chassis and supports comprehensive management via SNMP, WEB GUI, and CLI.
  • Online Firmware Upgrades: Supports remote/online software upgrades to maintain peak system performance and feature compatibility.
  • 19-Inch 1U Chassis with Dual-Power Hot Backup: Standard 19-inch 1U rackmount mechanical design featuring a modular power architecture that supports dual-power redundancy and hot backup.

Parameters

◆ Ethernet Interfaces (4 × 10/100Base-TX)

Protocols & Standards Compliant with IEEE 802.3 and IEEE 802.1Q (VLAN); Jumbo frames up to 2,036 Bytes
Interface Rate & Mode 10/100 Mbps adaptive, full/half-duplex auto-negotiation (Switching mode)
MAC Address Table Capacity 4,096 MAC address entries with dynamic learning
Physical Connectors 4 × RJ45 electrical ports supporting Auto-MDIX (crossover / straight-through adaptive)

◆ E1 Aggregation Interfaces (16 × E1)

Interface Standard Compliant with ITU-T G.703 (Selectable Framed / Unframed modes; 64 Kbps to 2,048 Kbps per E1)
Line Rate & Code 2,048 Kbps ± 50 ppm per E1; Line Code: HDB3
Impedance Options Unbalanced 75 Ω (with coaxial adapter for 75-2/3 coaxial cable) / Balanced 120 Ω
Jitter Characteristics Compliant with ITU-T G.742 and G.823 recommendations
Allowable Input Attenuation 0 to -6 dBm

◆ Power Supply & Working Environment

Power Input & Redundancy AC 110V/220V; DC -48V (Modular dual-power hot-backup redundancy supported)
Power Consumption < 15W
Operating Temperature 0°C to +50°C
Storage Temperature -40°C to +70°C
Operating Humidity 10% to 95% (Non-condensing)

Specifications

Model Number KDS-E16 Convergent Network Bridge
Product Name 4-Port Fast Ethernet to 16-Port E1 Convergent Network Bridge (Point-to-Multipoint Hub, 1U Rackmount)
Functional Description 16-channel E1 (75 Ω / 120 Ω optional) point-to-multipoint convergent network bridge to 4-port 10/100Base-TX Fast Ethernet switch with SNMP, WEB, and CLI management
Service Port Configuration 16 × E1 ports (75 Ω / 120 Ω), 4 × 10/100Base-TX Fast Ethernet ports, SNMP management interface
Power Supply AC 220V (110V/220V) or DC -48V (Optional), supports modular dual-power redundancy backup (< 15W)
Chassis & Dimensions 19-inch 1U Metal Rackmount Chassis (1.00 mm sheet metal), 430 mm × 140 mm (203 mm) × 44 mm / 44.5 mm (L × W × H)
Weight 2.7 kg / unit

Application

Interested in this product? Submit your inquiry below for a prompt response.

Scroll to Top