Product Categories

4-Port Ethernet to 16-Port E1 Converter (Inverse Multiplexing / EoPDH)

Overview

The 4-Port Ethernet to 16-Port E1 Converter (Model: KDS-E16F4) is a high-density, 19-inch 1U rackmount FPGA-based Ethernet-over-PDH (EoPDH) inverse multiplexing bridge engineered to bundle 1 to 16 E1 circuits into a single high-speed logical transport channel for four 10/100Base-TX Fast Ethernet interfaces. Delivering a single-E1 payload rate of 1,984 Kbps and an aggregate 16-channel throughput of up to 31,744 Kbps (16.384 Mbps adaptive line bandwidth), it provides seamless point-to-point interconnection between multi-E1 TDM networks and multi-port LAN infrastructures.

Built on proprietary ASIC/FPGA architecture, the KDS-E16F4 automatically detects active E1 links, supports hot-swappable E1 channels without interrupting live traffic, tolerates up to 100 ms of differential propagation delay across bundled circuits, and features configurable CRC error thresholds with asymmetric direction protection for carrier-grade reliability.

Features

  • Proprietary IC / FPGA Architecture: Engineered on a self-developed, proprietary IC/FPGA core for high integration and long-term operational stability.
  • Transparent Multi-E1 Ethernet Transport (1–16 E1): Achieves transparent Ethernet data transmission across 1 to 16 bundled E1 circuits with adaptive aggregate bandwidth up to 31,744 Kbps (16.384 Mbps).
  • Local & Remote Device Reset: Supports both local system reset and remote reset of the far-end device.
  • 4-Port Fast Ethernet & VLAN Support: Provides four 10/100Base-TX Fast Ethernet interfaces with full IEEE 802.1Q VLAN protocol compatibility.
  • Dynamic MAC Address Table & Frame Filtering: Features a built-in dynamic Ethernet MAC address table (4,096 entries) with local data frame filtering.
  • Comprehensive Ethernet Work Mode Support: Supports all standard Ethernet operating modes, including 10/100 Mbps auto-negotiation, full/half-duplex, and Auto-MDIX.
  • Configurable CRC Error Threshold & Asymmetric Protection: Allows setting automatic CRC error alarm thresholds to isolate degraded lines; if one direction of a 2M branch exceeds the error threshold, only that faulty direction is cut off while the opposite direction continues operating unaffected (supporting asymmetric bidirectional Ethernet transmission).
  • Differential Delay Tolerance (Up to 100 ms): Tolerates up to 100 ms of differential propagation delay across the 16 E1 channels; automatically suspends data transmission on any E1 circuit exceeding the allowable delay margin.
  • ITU-T Framed E1 Compliance: E1 interfaces conform to ITU-T G.703, G.704, and G.823 standards (signaling timeslots are not supported).
  • Integrated Clock Recovery & HDB3 Coding: E1 interface module incorporates built-in clock recovery circuitry and HDB3 line coding/decoding.
  • E1 Channel Hot-Plug & Auto-Detection: Supports hot-plugging of E1 channels without interrupting active data transmission, automatically detecting and utilizing available E1 links.
  • Flexible Multi-E1 Auto-Configuration: Supports flexible 1 to 16 E1 channel configuration, automatically detecting the number of active E1s and selecting valid circuits.

Parameters

◆ E1 Interface (16-Channel Inverse Multiplexing)

Interface & Framing Standards Compliant with ITU-T G.703, G.704, and G.823 (Signaling timeslots not supported)
Line Rate & Aggregate Payload N × 64 Kbps ± 50 ppm (1,984 Kbps per E1; up to 31,744 Kbps across 16 × E1, adaptive 16.384 Mbps line bandwidth); Line Code: HDB3
Differential Delay Tolerance Up to 100 ms maximum delay difference across 16 E1 channels
Impedance Options 75 Ω (unbalanced coaxial) / 120 Ω (balanced twisted-pair)
Jitter Tolerance Compliant with ITU-T G.742 and G.823 recommendations
Allowed Input Attenuation 0 to -6 dBm

◆ Ethernet Interface (4 × 10/100M)

Interface Rate 10/100 Mbps adaptive, full/half-duplex auto-negotiation
Protocols & Standards Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)
MAC Address Table Capacity 4,096 MAC address entries with dynamic learning and local frame filtering
Physical Connectors 4 × RJ45 electrical ports supporting Auto-MDIX

◆ Working Environment

Operating Temperature -10°C to +50°C
Operating Humidity 5% to 95% (Non-condensing)
Storage Temperature -40°C to +80°C
Storage Humidity 5% to 95% (Non-condensing)

Specifications

Model Number KDS-E16F4
Product Name 4-Port Ethernet to 16-Port E1 Converter (Inverse Multiplexing / EoPDH, 1U Rackmount)
Functional Description Bidirectional 1–16 × E1 inverse multiplexing to 4-channel 10/100Base-TX Fast Ethernet protocol converter (adaptive 16.384 Mbps line bandwidth, up to 31,744 Kbps aggregate payload)
Port Configuration 16 × E1 interfaces (75 Ω / 120 Ω), 4 × 10/100Base-TX Fast Ethernet RJ45 interfaces
Power Input & Consumption Power Supply Options: AC 180V–260V / DC -48V / DC +24V (optional)  |  Power Consumption: ≤ 10W
Dimensions 19-inch 1U Rackmount Enclosure, 483 mm × 138 mm × 44 mm (W × D × H)

Application

4-Port Ethernet to 16-Port E1 Converter (Inverse Multiplexing EoPDH) Topology

 

Interested in this product? Submit your inquiry below for a prompt response.

Scroll to Top