Product Categories

Optical Ethernet (1×9) to Framed E1 Converter

Overview

The Optical Ethernet (1×9) to Framed E1 Converter is a compact desktop FPGA-based self-learning Ethernet-over-PDH (EoPDH) protocol bridge engineered to transport 10/100Base-FX optical Fast Ethernet traffic over a single framed E1 circuit with arbitrary timeslot allocation (64 Kbps to 2,048 Kbps). Leveraging existing PDH, SDH, or microwave networks providing E1 channels, it enables cost-effective local-to-remote optical Ethernet extension with built-in diagnostic loopback capabilities for streamlined commissioning and routine maintenance.

Featuring non-intrusive OAM remote monitoring, local-to-remote rate follow synchronization, SNMP network management, remote temperature and voltage telemetry, three loopback test modes (ANA, DIG, REM), and multi-node management chaining across optical modems and fiber transceivers, this unit delivers reliable carrier-grade performance in a desktop enclosure.

Features

  • Proprietary IC / FPGA Architecture: Engineered on a self-developed, proprietary IC/FPGA core for high integration, low power consumption, and long-term operational stability.
  • Non-Intrusive Remote OAM Management: Enables monitoring and control of remote equipment via dedicated OAM channels without occupying user payload timeslots, preserving E1 bandwidth.
  • Arbitrary Framed E1 Timeslot Allocation (64K–2048K): Supports flexible timeslot selection on the framed E1 interface with configurable payload rates from 64 Kbps to 2,048 Kbps.
  • Local-to-Remote Rate Follow Synchronization: Allows the local unit to force the remote unit’s operating rate to follow the local timeslot configuration automatically in framed mode.
  • Automatic E1 Loopback Protection: Includes E1 interface loopback detection to prevent converter crashes caused by accidental line loopbacks.
  • Power-Off & E1 Fault Alarm Indicators: Provides dedicated status indicators for device power-off, E1 line disconnection, and Loss of Signal (LOS).
  • Link-Down Propagation Control on E1 Loss: Can be configured to suppress sending LINK-down signals to the Ethernet interface when the E1 line is broken.
  • Jumbo Frame Support (Up to 2,036 Bytes): Ethernet interface supports jumbo frames up to 2,036 bytes.
  • Dynamic MAC Address Table & Frame Filtering: Features a built-in dynamic Ethernet MAC address table (4,096 entries) with local data frame filtering.
  • 100 Mbps Full-Duplex & VLAN Support: Optical Ethernet interface supports 100 Mbps full-duplex operation and IEEE 802.1Q VLAN protocols.
  • Ethernet Watchdog Self-Reset: Incorporates an automated Ethernet monitor self-reset mechanism to prevent system hang-ups.
  • Dual Clock Synchronization Modes: Provides two selectable clock modes: internal E1 master clock and E1 line recovered clock.
  • Three Diagnostic Loopback Modes: Supports E1 interface loopback (ANA), Ethernet interface loopback (DIG), and commanded remote Ethernet interface loopback (REM).
  • Dual E1 Impedance Options: Supports both 75 Ω unbalanced coaxial and 120 Ω balanced twisted-pair E1 interfaces.
  • SNMP Network Management: Supports standard SNMP network management for centralized supervision.
  • Remote Temperature & Voltage Monitoring: Allows the local unit to monitor the remote equipment’s operating temperature and power supply voltage.
  • Cascaded Multi-Node Management Topology: Supports forming a chained structure of Ethernet E1 Bridge (A) — Optical Ethernet Modem (B) — Ethernet Optical Fiber Transceiver (C), enabling centralized management of (B) and (C) from (A).

Parameters

◆ E1 Interface (Framed)

Interface & Framing Standards Compliant with ITU-T G.703 and G.704 (Arbitrary timeslot allocation: 64 Kbps to 2,048 Kbps)
Line Rate & Code N × 64 Kbps (up to 2,048 Kbps ± 50 ppm); Line Code: HDB3
Impedance Options Unbalanced 75 Ω (with 75-2/3 coaxial cable adapter) / Balanced 120 Ω
Jitter Characteristics Compliant with ITU-T G.742 and G.823 recommendations
Allowable Input Attenuation 0 to -6 dBm

◆ Optical Ethernet Interface (10/100Base-FX)

Interface Rate & Mode 100 Mbps full-duplex (10/100Base-FX optical interface)
Protocols & Standards Compliant with IEEE 802.3az and IEEE 802.1Q (VLAN); Jumbo frames up to 2,036 Bytes
MAC Address Table Capacity 4,096 MAC address entries with dynamic learning and local frame filtering
Physical Connector 1 × 1×9 optical Ethernet port

◆ Working Environment & Reliability

Operating Temperature -10°C to +60°C
Operating Humidity 0% to 95% (Non-condensing)
Storage Temperature -40°C to +85°C
Reliability (MTBF) > 100,000 hours

Specifications

Product Name Optical Ethernet (1×9) to Framed E1 Converter (Desktop)
Functional Description 1-channel Framed E1 to 10/100Base-FX optical Fast Ethernet protocol converter with arbitrary timeslot allocation, OAM, SNMP, and multi-mode loopback diagnostics
Port Configuration 1 × Framed E1 interface (75 Ω / 120 Ω), 1 × 1×9 optical Ethernet port
Power Input & Consumption Power Supply Options: AC 180V–260V / DC -48V / DC +24V  |  Power Consumption: ≤ 5W
Chassis & Dimensions Desktop Enclosure, 216 mm × 138 mm × 41 mm (W × D × H)
Weight 1.3 kg / pc

Application

Interested in this product? Submit your inquiry below for a prompt response.

Scroll to Top