Overview
The Optical Ethernet (1×9) to Unframed E1 Converter is a compact desktop FPGA-based self-learning Ethernet-over-PDH (EoPDH) protocol bridge engineered to transport 10/100Base-FX optical Fast Ethernet traffic over a single unframed E1 circuit. Leveraging existing PDH, SDH, or microwave networks providing E1 channels, it enables cost-effective local-to-remote optical Ethernet extension with built-in diagnostic loopback capabilities for streamlined commissioning and routine maintenance.
Featuring non-intrusive OAM remote monitoring, SNMP network management, remote temperature and voltage telemetry, three loopback test modes (ANA, DIG, REM), and multi-node management chaining across optical modems and fiber transceivers, this unit delivers reliable carrier-grade performance in a desktop enclosure.
Features
- Proprietary IC / FPGA Architecture: Engineered on a self-developed, proprietary IC/FPGA core for high integration, low power consumption, and long-term operational stability.
- Non-Intrusive Remote OAM Management: Enables monitoring and control of remote equipment via dedicated OAM channels without occupying user payload timeslots, preserving E1 bandwidth.
- Configurable Timeslot & Rate (64K–2048K): Supports flexible timeslot configuration on the E1 link with payload rates adjustable from 64 Kbps to 2,048 Kbps.
- Local-to-Remote Rate Follow (Framed Mode): Allows the local unit to force the remote unit’s operating rate to follow the local setting (valid when operating in framed mode).
- Automatic E1 Loopback Protection: Includes E1 interface loopback detection to prevent converter crashes caused by accidental line loopbacks.
- Power-Off & E1 Fault Alarm Indicators: Provides status indicators for device power-off, E1 line disconnection, and Loss of Signal (LOS).
- Link-Down Propagation Control on E1 Loss: Can be configured to suppress sending LINK-down signals to the Ethernet interface when the E1 line is broken.
- Jumbo Frame Support (Up to 2,036 Bytes): Ethernet interface supports jumbo frames up to 2,036 bytes.
- Dynamic MAC Address Table & Frame Filtering: Features a built-in dynamic Ethernet MAC address table (4,096 entries) with local data frame filtering.
- 100 Mbps Full-Duplex & VLAN Support: Optical Ethernet interface supports 100 Mbps full-duplex operation and IEEE 802.1Q VLAN protocols.
- Ethernet Watchdog Self-Reset: Incorporates an automated Ethernet monitor self-reset mechanism to prevent system hang-ups.
- Dual Clock Synchronization Modes: Provides two selectable clock modes: internal E1 master clock and E1 line recovered clock.
- Three Diagnostic Loopback Modes: Supports E1 interface loopback (ANA), Ethernet interface loopback (DIG), and commanded remote Ethernet interface loopback (REM).
- Dual E1 Impedance Options: Supports both 75 Ω unbalanced coaxial and 120 Ω balanced twisted-pair E1 interfaces.
- SNMP Network Management: Supports standard SNMP network management for centralized supervision.
- Remote Temperature & Voltage Monitoring: Allows the local unit to monitor the remote equipment’s operating temperature and power supply voltage.
- Cascaded Multi-Node Management Topology: Supports forming a chained structure of Ethernet E1 Bridge (A) — Optical Ethernet Modem (B) — Ethernet Optical Fiber Transceiver (C), enabling centralized management of (B) and (C) from (A).
Parameters
◆ E1 Interface (Unframed)
| Interface Standard | Compliant with ITU-T G.703 |
| Line Rate & Code | 2,048 Kbps ± 50 ppm; Line Code: HDB3 |
| Impedance Options | Unbalanced 75 Ω (with 75-2/3 coaxial cable adapter) / Balanced 120 Ω |
| Jitter Characteristics | Compliant with ITU-T G.742 and G.823 recommendations |
| Allowable Input Attenuation | 0 to -6 dBm |
◆ Optical Ethernet Interface (10/100Base-FX)
| Interface Rate & Mode | 100 Mbps full-duplex (10/100Base-FX optical interface) |
| Protocols & Standards | Compliant with IEEE 802.3az and IEEE 802.1Q (VLAN); Jumbo frames up to 2,036 Bytes |
| MAC Address Table Capacity | 4,096 MAC address entries with dynamic learning and local frame filtering |
| Physical Connector | 1 × 1×9 optical Ethernet port |
◆ Working Environment & Reliability
| Operating Temperature | -10°C to +60°C |
| Operating Humidity | 0% to 95% (Non-condensing) |
| Storage Temperature | -40°C to +85°C |
| Reliability (MTBF) | > 100,000 hours |
Specifications
| Product Name | Optical Ethernet (1×9) to Unframed E1 Converter (Desktop) |
| Functional Description | 1-channel Unframed E1 to 10/100Base-FX optical Fast Ethernet protocol converter with OAM, SNMP, and multi-mode loopback diagnostics |
| Port Configuration | 1 × Unframed E1 interface (75 Ω / 120 Ω), 1 × 1×9 optical Ethernet port |
| Power Input & Consumption | Power Supply Options: AC 180V–260V / DC -48V / DC +24V | Power Consumption: ≤ 5W |
| Chassis & Dimensions | Desktop Enclosure, 216 mm × 138 mm × 41 mm (W × D × H) |
| Weight | 1.3 kg / pc |
Application


