Product Categories

3-Port Ethernet to 4-Port E1 Converter (Console Management)

Overview

The 3-Port Ethernet to 4-Port E1 Converter with Console Management is a high-performance, compact desktop FPGA-based Ethernet-over-PDH (EoPDH) inverse multiplexing bridge engineered to bundle 1 to 4 E1 circuits into a single high-speed logical transport channel (up to 8.192 Mbps adaptive bandwidth) for three 10/100Base-T Fast Ethernet interfaces, equipped with an dedicated Console network management port.

Featuring flexible 1–4 E1 auto-configuration, automatic differential delay compensation (up to 100 ms), configurable CRC error thresholds with asymmetric direction protection, hot-swappable E1 channel support, and local/remote status monitoring, this reliable multi-service gateway ensures seamless LAN extension over existing TDM infrastructures.

Features

  • Proprietary IC / FPGA Architecture: Engineered on a self-developed, proprietary IC/FPGA core for high integration, low power consumption, and long-term operational stability.
  • Transparent Multi-E1 Ethernet Transport (1–4 E1): Achieves transparent Ethernet data transmission across 1 to 4 bundled E1 circuits with adaptive aggregate bandwidth up to 7,936 Kbps (8.192 Mbps line rate).
  • Local & Remote Device Reset: Supports both local system reset and remote reset of the far-end device.
  • 3-Port Fast Ethernet & VLAN Support: Provides three 10/100Base-T Fast Ethernet interfaces with full IEEE 802.3az and IEEE 802.1Q VLAN protocol compatibility.
  • Dynamic MAC Address Table & Frame Filtering: Features a built-in dynamic Ethernet MAC address table (4,096 entries) with local data frame filtering.
  • High Aggregate Bandwidth (Up to 7,936 Kbps): Delivers a payload line rate of 1,984 Kbps per single E1 circuit, scaling up to 7,936 Kbps across all 4 bundled E1 channels.
  • Comprehensive Ethernet Work Mode Support: Supports all standard Ethernet operating modes with full/half-duplex auto-negotiation and Auto-MDIX cable adaptation.
  • Configurable CRC Error Threshold & Asymmetric Protection: Allows setting automatic CRC error alarm thresholds to isolate degraded lines; if one direction of a 2M branch exceeds the error threshold, only that faulty direction is cut off while the opposite direction continues operating unaffected (supporting asymmetric bidirectional Ethernet transmission).
  • Differential Delay Tolerance (Up to 100 ms): Tolerates up to 100 ms of differential propagation delay across the 4 E1 channels; automatically suspends data transmission on any E1 circuit exceeding the allowable delay margin.
  • ITU-T Framed E1 Compliance: E1 interfaces conform to ITU-T G.703, G.704, and G.823 standards (signaling timeslots are not supported).
  • Integrated Clock Recovery & HDB3 Coding: E1 interface modules incorporate built-in clock recovery circuitry and HDB3 line coding/decoding.
  • Dedicated Console Management Port: Equipped with a dedicated Console network management interface for straightforward installation, configuration, and maintenance.
  • Remote Equipment Status Monitoring: Supports real-time viewing and display of remote equipment working status from the local end.
  • E1 Channel Hot-Plug & Auto-Detection: Supports hot-plugging of E1 channels without interrupting active data transmission, automatically detecting and utilizing available E1 links during reset.

Parameters

◆ E1 Interface (4-Channel Inverse Multiplexing)

Interface & Framing Standards Compliant with ITU-T G.703, G.704, and G.823 (Signaling timeslots not supported)
Interface Rate & Code 2,048 Kbps ± 50 ppm; Line Code: HDB3
Impedance Options Unbalanced 75 Ω (with 75-2/3 coaxial adapter) / Balanced 120 Ω
Jitter Characteristics Compliant with ITU-T G.742 and G.823 recommendations
Allowed Input Attenuation 0 to -6 dBm

◆ Ethernet Interface (3 × 10/100M) & Console

Interface Rate & Protocols 10/100 Mbps adaptive, full/half-duplex auto-negotiation; IEEE 802.3az, IEEE 802.1Q (VLAN)
MAC Address Table Capacity 4,096 MAC address entries with dynamic learning and local frame filtering
Physical Connectors 3 × RJ45 electrical ports supporting Auto-MDIX; 1 × Console management port

◆ Working Environment

Operating Temperature -10°C to +60°C
Operating Humidity 0% to 95% (Non-condensing)
Storage Temperature -40°C to +85°C
Reliability (MTBF) > 100,000 hours

Specifications

Product Name 3-Port Ethernet to 4-Port E1 Converter (Console Management, Desktop)
Functional Description Bidirectional 1–4 × E1 inverse multiplexing to 3-channel 10/100Base-T Fast Ethernet protocol converter with Console network management (adaptive 8.192 Mbps line bandwidth)
Port Configuration 4 × E1 interfaces (75 Ω / 120 Ω), 3 × 10/100Base-T Fast Ethernet RJ45 interfaces, 1 × Console management port
Power Input & Consumption Power Supply Options: AC 180V–260V / DC -48V / DC +24V  |  Power Consumption: ≤ 5W
Chassis & Dimensions Compact Desktop Enclosure, 216 mm × 138 mm × 41 mm (W × D × H)
Weight 1.3 kg / pc

Application

Interested in this product? Submit your inquiry below for a prompt response.

Scroll to Top