Product Categories

Ethernet to 4-Port E1 Converter (Dual Impedance 75Ω/120Ω)

Overview

The Ethernet to 4-Port E1 Converter (Model: KDS-E4F1) is a high-integration, 19-inch 1U rackmount Ethernet-over-PDH (EoPDH) inverse multiplexing bridge designed to bundle 1 to 4 E1 circuits into a single logical high-speed channel for 10/100Base-T Ethernet traffic. Utilizing standard GFP encapsulation and supporting LCAS and LAPS protocols, it delivers a single-E1 line rate of 1,984 Kbps and an aggregate 4-channel Ethernet throughput of up to 7,936 Kbps.

Equipped with dual-impedance E1 interfaces (supporting both 75 Ω unbalanced and 120 Ω balanced connections on the front panel), standalone SNMP network management, and E1 channel hot-swap detection, the KDS-E4F1 provides high stability, low power consumption, and comprehensive fault alarm management for carrier LAN interconnection, local-end aggregation, video-on-demand, and remote surveillance networks.

Features

  • Transparent Multi-E1 Ethernet Transport: Achieves transparent Ethernet data transmission across 1 to 4 bundled E1 circuits (architecture scalable up to 8 E1 channels).
  • Local & Remote Device Reset: Supports both local system reset and remote reset of the far-end device.
  • Fast Ethernet & VLAN Protocol Support: Provides 10/100 Mbps Fast Ethernet connectivity with full IEEE 802.1Q VLAN protocol compatibility.
  • Dynamic MAC Address Table & Frame Filtering: Features a built-in dynamic Ethernet MAC address table (4,096 entries) with local traffic frame filtering.
  • High Aggregate Bandwidth (Up to 7,936 Kbps): Delivers a payload line rate of 1,984 Kbps per single E1 circuit and up to 7,936 Kbps across 4 bundled E1 channels.
  • Comprehensive Ethernet Work Mode Support: Supports all standard Ethernet operating modes, including 10/100 Mbps auto-negotiation, full/half-duplex, and Auto-MDIX.
  • Configurable CRC Error Threshold & Asymmetric Protection: Allows setting automatic CRC error alarm thresholds to isolate degraded lines; if one direction of a 2M branch exceeds the error threshold, only that faulty direction is cut off while the opposite direction continues operating unaffected (supporting asymmetric bidirectional Ethernet transmission).
  • Differential Delay Tolerance (Up to 100 ms): Tolerates up to 100 ms of differential propagation delay across the 4 E1 channels; automatically suspends data transmission on any E1 circuit exceeding the allowable delay margin.
  • ITU-T Framed E1 Compliance: E1 interfaces conform to ITU-T G.703, G.704, and G.823 standards (signaling timeslots are not supported).
  • Integrated Clock Recovery & HDB3 Coding: E1 interface module incorporates built-in clock recovery circuitry and HDB3 line coding/decoding.
  • E1 Channel Hot-Plug & Auto-Detection: Supports hot-plugging of E1 channels without interrupting active data transmission, automatically detecting and utilizing available E1 links.
  • Flexible 4-Channel E1 Auto-Configuration: Supports flexible 4-channel E1 configuration, automatically detecting the number of active E1s and selecting valid circuits.

Parameters

◆ E1 Interface (4-Channel Dual-Impedance Inverse Multiplexing)

Interface & Framing Standards Compliant with ITU-T G.703, G.704, and G.823 (Signaling timeslots not supported)
Encapsulation & Protocols GFP encapsulation; LCAS and LAPS protocols supported
Line Rate & Aggregate Payload N × 64 Kbps ± 50 ppm (1,984 Kbps per E1; up to 7,936 Kbps across 4 × E1); Line Code: HDB3
Differential Delay Tolerance Up to 100 ms maximum delay difference across 4 E1 channels
Impedance Options Dual-impedance hardware interfaces: 75 Ω (unbalanced coaxial) and 120 Ω (balanced twisted-pair)
Jitter Performance Compliant with ITU-T G.742 and G.823 recommendations
Allowed Input Attenuation 0 to -6 dBm

◆ Ethernet Interface (10/100M)

Interface Rate 10/100 Mbps adaptive, full/half-duplex auto-negotiation
Protocols & Standards Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)
MAC Address Table Capacity 4,096 MAC address entries with dynamic learning and local frame filtering
Physical Connector 1 × RJ45 electrical port supporting Auto-MDIX

◆ Working Environment

Operating Temperature -10°C to +50°C
Operating Humidity 5% to 95% (Non-condensing)
Storage Temperature -40°C to +80°C
Storage Humidity 5% to 95% (Non-condensing)

Specifications

Model Number KDS-E4F1 (1U Rackmount Dual-Impedance Version)
Product Name Ethernet to 4-Port E1 Converter (Dual Impedance 75Ω/120Ω, 1U Rackmount)
Functional Description Bidirectional 1–4 × E1 inverse multiplexing (GFP / LCAS / LAPS) to 10/100Base-T Fast Ethernet protocol converter with dual 75 Ω + 120 Ω E1 interfaces and standalone SNMP management
Port Configuration 4 × Dual-Impedance E1 interfaces (75 Ω & 120 Ω), 1 × 10/100Base-T Fast Ethernet RJ45 interface
Power Input & Consumption Power Supply Options: AC 180V–260V / DC -48V / DC +24V  |  Power Consumption: ≤ 10W
Dimensions 19-inch 1U Rackmount Enclosure, 483 mm × 138 mm × 44 mm (W × D × H)

Application

Interested in this product? Submit your inquiry below for a prompt response.

Scroll to Top