Product Categories

Ethernet to E1 Converter (Framed E1)

Overview

The Ethernet to E1 Converter (Model: KDS-E1fF1) is a high-performance, self-learning Ethernet-over-E1 protocol bridge designed to transport 10/100Base-T Ethernet data transparently across a framed E1 channel (N × 64 Kbps, up to 2048 Kbps). Acting as an efficient LAN extension gateway, it leverages existing TDM transport networks—including PDH, SDH, and microwave links—to establish cost-effective, point-to-point Ethernet interconnections between remote sites.

Equipped with flexible timeslot allocation, SNMP network management, out-of-band OAM remote monitoring that preserves user payload bandwidth, and built-in multi-mode diagnostic loopback functions, the KDS-E1fF1 ensures simplified commissioning, reliable operation, and effortless routine maintenance for telecom operators and enterprise networks.

Features

  • Flexible Framed E1 Timeslot Allocation: Supports arbitrary E1 timeslot configuration (N × 64 Kbps), delivering selectable transmission bandwidth from 64 Kbps to 2048 Kbps.
  • Out-of-Band OAM Remote Management: Enables monitoring and control of remote devices via dedicated OAM management channels without occupying user timeslots or sacrificing payload bandwidth.
  • Automatic Loopback Detection & Loop Prevention: Features built-in E1 interface loopback detection to prevent network storms and switch crashes caused by accidental line loops.
  • Remote Power Failure vs. Link Loss Differentiation: Accurately distinguishes between remote device power loss and physical E1 line disconnection during signal loss events.
  • Ethernet Link Fault Pass-Through (LFP): Supports configurable E1 failover, shutting down the Ethernet LINK signal upon E1 line faults to trigger upstream network redundancy.
  • Jumbo Frame Support: Ethernet interface supports oversized frames up to 2,036 bytes in length.
  • Multi-Port Ethernet Isolation Capability: Supports port-based isolation across 4-channel 10/100M Ethernet configurations to ensure independent, secure communication.
  • Auto-Negotiating Ethernet Connectivity: Supports 10M/100M Ethernet rates, full/half-duplex auto-negotiation, IEEE 802.1Q VLAN tagging, and Auto-MDIX crossover/straight-through adaptation.
  • Flexible Clock Synchronization Modes: Provides two selectable timing modes: E1 Master (Internal) clock and E1 Line Slave (Recovered) clock.
  • Three Diagnostic Loopback Modes: Supports E1 local loopback (ANA), Ethernet local loopback (DIG), and remote Ethernet loopback (REM) for rapid fault isolation.
  • Hardware Watchdog Auto-Reset: Incorporates internal Ethernet data traffic monitoring with automatic system reset to prevent lockups or crashes.
  • Remote Environmental & Power Telemetry: Enables the local unit to monitor the operating temperature and input voltage of the remote device in real time.
  • Dual E1 Impedance Compatibility: Supports both 120 Ω (balanced twisted-pair) and 75 Ω (unbalanced coaxial) E1 interfaces natively without requiring additional manual configuration.
  • SNMP Network Management Support: Supports standard SNMP protocol for centralized, visual network management and status monitoring.

Parameters

◆ E1 Interface

Interface Standard Compliant with ITU-T G.703 and G.704 (Framed) recommendations
Line Rate & Coding N × 64 Kbps ± 50 ppm (64 Kbps to 2048 Kbps); Line Code: HDB3
Impedance Options 75 Ω (unbalanced coaxial) / 120 Ω (balanced twisted-pair) auto-adapting
Jitter Performance Compliant with ITU-T G.742 and G.823 recommendations
Allowed Input Attenuation 0 to -6 dBm

◆ Ethernet Interface (10/100M)

Interface Rate 10/100 Mbps adaptive, full/half-duplex auto-negotiation
Protocols & Standards Compatible with IEEE 802.3, IEEE 802.1Q (VLAN); Jumbo Frames up to 2,036 bytes
MAC Address Table Capacity 4,096 MAC address entries with dynamic learning
Physical Connector RJ45 electrical port supporting Auto-MDIX

◆ Working Environment

Operating Temperature -10°C to +50°C
Operating Humidity 5% to 95% (Non-condensing)
Storage Temperature -40°C to +80°C
Storage Humidity 5% to 95% (Non-condensing)

Specifications

Model Number KDS-E1fF1
Product Name Ethernet to E1 Converter (Framed E1, Desktop)
Functional Description 1-channel framed E1 (N × 64 Kbps) to Fast Ethernet (10/100M) protocol converter with E1 loopback detection and SNMP management
Port Configuration 1 × Framed E1 interface (75 Ω / 120 Ω), 1 × 10/100Base-T Fast Ethernet RJ45 interface
Power Input & Consumption Power Supply Options: AC 180V–260V / DC -48V / DC +24V  |  Power Consumption: ≤ 10W
Dimensions Desktop Enclosure, 216 mm × 140 mm × 31 mm (W × D × H)
Weight 1.1 kg / pc

Application

Interested in this product? Submit your inquiry below for a prompt response.

Scroll to Top