Product Categories

Ethernet to E1 Converter (Unframed E1)

Overview

The Ethernet to E1 Converter (Model: KDS-E1F1) is a high-performance, self-learning Ethernet-over-E1 protocol bridge designed to transport 10/100Base-T Ethernet traffic transparently across an unframed 2048 Kbps E1 channel. Acting as an efficient LAN extension gateway, it leverages existing TDM transport infrastructures—such as PDH, SDH, and microwave links—to establish cost-effective, point-to-point Ethernet interconnections between remote sites.

Equipped with 1 unframed E1 service port, 1 Fast Ethernet RJ45 electrical interface, and integrated multi-mode diagnostic loopback capabilities, the KDS-E1F1 provides out-of-band remote device management without consuming payload bandwidth, delivering reliable network extension and simplified commissioning for telecom carriers and enterprise networks.

Features

  • Unframed 2048K E1 & Out-of-Band Management: Operates in full unframed 2048 Kbps E1 mode with remote device status management; overhead management traffic does not occupy user payload bandwidth.
  • Automatic Loopback Detection & Broadcast Storm Prevention: Detects E1 loopback conditions with visual LED alerts and automatically blocks Ethernet frames sharing identical source and destination MAC addresses to prevent network switch crashes.
  • Remote Power Failure vs. Link Loss Differentiation: Accurately distinguishes between remote device power outages and E1 physical line disconnections upon signal loss.
  • Ethernet Link Fault Pass-Through (LFP / E1 Failover): Supports configurable E1 failover, shutting down the Ethernet LINK signal when an E1 line fault occurs to trigger upstream routing redundancy.
  • Jumbo Frame Support: Supports oversized Ethernet frames up to 2,036 bytes in length.
  • Dynamic MAC Address Learning & Filtering: Features a built-in dynamic Ethernet MAC address table (4,096 entries) with local traffic frame filtering.
  • Auto-Negotiating Fast Ethernet Connectivity: Supports 10M/100M Ethernet rates, full/half-duplex auto-negotiation, IEEE 802.1Q VLAN tagging, and Auto-MDIX crossover/straight-through adaptation.
  • Hardware Watchdog Auto-Reset: Incorporates internal Ethernet data traffic monitoring with automatic system reset to prevent lockups or crashes.
  • Flexible Clock Synchronization Modes: Supports two selectable timing modes: E1 Master (Internal) clock and E1 Line Slave (Recovered) clock.
  • Remote Speed Synchronization: Capable of forcing the remote device’s Ethernet port speed to match the local unit (applicable in framed operation).
  • Three Diagnostic Loopback Modes: Supports E1 local loopback (ANA), Ethernet local loopback (DIG), and remote Ethernet loopback (REM) for rapid fault isolation.
  • Dual E1 Impedance Compatibility: Supports both 120 Ω (balanced twisted-pair) and 75 Ω (unbalanced coaxial) E1 interfaces natively without requiring manual jumper or DIP switch settings.
  • Environmental & Power Telemetry: Monitors and configures temperature alarm thresholds while tracking operating voltage and temperature for both local and remote devices.
  • Multi-Stage Hybrid Topology Support (Type 1): Supports hybrid cascading topologies: Ethernet-E1 Bridge (A) — E1 Fiber Modem (B) — Ethernet Fiber Modem (C).
  • End-to-End Managed Hybrid Topology (Type 2): Supports managed cascading topologies: Ethernet-E1 Bridge (A) — Optical Ethernet-E1 Bridge (B) — Ethernet Fiber Media Converter (C), with centralized remote management of Nodes B and C from Node A.

Parameters

◆ E1 Interface

Interface Standard Compliant with ITU-T G.703 recommendations
Line Speed & Coding 2048 Kbps ± 50 ppm; Line Code: HDB3
Impedance Options 75 Ω (unbalanced coaxial) / 120 Ω (balanced twisted-pair) auto-adapting
Jitter Performance Compliant with ITU-T G.742 and G.823 recommendations
Allowed Input Attenuation 0 to -6 dBm

◆ Ethernet Interface (10/100M)

Interface Rate 10/100 Mbps adaptive, full/half-duplex auto-negotiation
Protocols & Standards Compatible with IEEE 802.3, IEEE 802.1Q (VLAN); Jumbo Frames up to 2,036 bytes
MAC Address Table Capacity 4,096 MAC address entries with dynamic learning
Physical Connector 1 × RJ45 electrical port supporting Auto-MDIX

◆ Working Environment

Operating Temperature -10°C to +50°C
Operating Humidity 5% to 95% (Non-condensing)
Storage Temperature -40°C to +80°C
Storage Humidity 5% to 95% (Non-condensing)

Specifications

Model Number KDS-E1F1
Product Name Ethernet to E1 Converter (Unframed E1)
Functional Description 1-channel unframed E1 to Fast Ethernet (10/100M) protocol converter with built-in E1 loopback detection and remote management
Port Configuration 1 × E1 interface (75 Ω / 120 Ω), 1 × 10/100Base-T Fast Ethernet RJ45 interface
Power Input & Consumption Power Supply Options: AC 180V–260V / DC -48V / DC +24V  |  Power Consumption: ≤ 10W
Dimensions & Weight Mini Desktop Type: 216 mm × 140 mm × 31 mm (W × D × H), 1.3 kg / pc
19-inch 1U Rackmount Type: 483 mm × 138 mm × 44 mm (W × D × H), 2.0 kg / pc

Application

Interested in this product? Submit your inquiry below for a prompt response.

Scroll to Top