Product Categories

8E1 TDM over IP Converter

Overview

The 8E1 TDM over IP (TDMoIP) Converter (Model: KDS-E8) is a carrier-grade circuit emulation device designed to transparently transmit up to 8 legacy E1 TDM streams over standard packet-switched IP networks (LAN/WAN/MAN and wireless backhaul). It allows telecom operators and enterprise users to seamlessly interconnect legacy TDM infrastructure—such as PBXs, cellular base stations, SS7 signaling gateways, and voicemail systems—over cost-effective Ethernet architectures without compromising voice quality or clock synchronization integrity.

Equipped with 8 E1 service interfaces, 2 Gigabit Ethernet RJ45 ports, 1 Gigabit SFP optical uplink slot, and dual Console/Web management access, the KDS-E8 delivers low-latency transmission, high bandwidth utilization, and high reliability for modern network transitions.

Features

  • High-Performance Core Processor: Powered by an 32-bit ARM Cortex-M4 processor operating at 192 MHz for high-efficiency encapsulation and protocol processing.
  • Industrial Protection Enclosure: Built with an anodized aluminum alloy casing rated at IP40 protection grade, built to operate in harsh industrial environments.
  • Flexible Network Management: Supports intuitive Web GUI and Console CLI management interfaces for simplified installation, configuration, and real-time link monitoring.
  • High Interface Density: Provides 8 × E1 service ports, 2 × 10/100/1000M Ethernet RJ45 interfaces, and 1 × 100/1000M adaptive SFP optical uplink port.
  • Native E1 Impedance Auto-Sensing: Supports both 75 Ω (unbalanced coaxial) and 120 Ω (balanced twisted-pair) E1 interfaces with native auto-adaptation, eliminating manual DIP switch adjustments.
  • Standard-Compliant Circuit Emulation: Transparently transports framed and unframed E1 (N×64Kbps) traffic over IP/Ethernet packet networks in strict compliance with ITU-T G.703 standards.
  • Advanced Clock Recovery Architecture: Incorporates proprietary clock restoration algorithm technology to ensure ultra-low jitter and wander performance, fully compliant with ITU-T G.823, G.824, and G.8261 recommendations.
  • High Efficiency & Low Latency: Offers optimized packet transmission with configurable packet lengths, IEEE 802.1Q VLAN tagging, and Jumbo Frame support to maintain minimal end-to-end latency.
  • Comprehensive Link Loss Indication (LLI): Features automatic E1 Link Loss Indication to immediately notify remote equipment of local link failures.
  • Diagnostic Loopback & Port Control: Supports local and remote E1 channel loopback testing alongside individual E1 port enablement settings for rapid troubleshooting.
  • Maximized Bandwidth Utilization: Optimizes packet overhead to achieve up to 90% bandwidth transmission efficiency across IP networks.
  • Remote Firmware Management: Supports online local and remote hardware/firmware upgrades directly via the Web GUI interface.
  • Versatile Power Supply Options: Flexible power input architecture supporting AC 180V–260V, DC -48V, or DC +24V power supplies.

Parameters

◆ Ethernet Interface (10/100/1000M)

Protocols & Standards IEEE 802.3az, IEEE 802.1Q (VLAN), Jumbo Frames supported
Interface Rate 10/100/1000 Mbps adaptive, full/half-duplex auto-negotiation
MAC Address Table Capacity 4,096 MAC address entries with auto-learning
Physical Connectors 2 × RJ45 electrical ports with Auto-MDI/MDIX support
Optical Port 1 × 100/1000M adaptive Ethernet SFP optical slot

◆ E1 Interface

Interface Standard Compliant with ITU-T G.703 recommendations
Line Speed & Coding 2048 kbps ± 50 ppm; Line Code: HDB3
Impedance Options 75 Ω (unbalanced coaxial adapter) / 120 Ω (balanced twisted-pair) auto-adapting
Jitter & Drift Performance Compliant with ITU-T G.742, G.823, G.824, G.8261 recommendations
Allowed Input Attenuation 0 to -6 dBm

◆ Environmental & Mechanical Indicators

Operating Temperature -10°C to +60°C
Storage Temperature -40°C to +85°C
Working Humidity 0% to 95% (Non-condensing)
Enclosure & Protection Anodized aluminum alloy shell, IP40 protection grade
MTBF > 100,000 Hours

Specifications

Model Number KDS-E8
Product Name 8E1 TDM over IP Converter
Functional Description Encapsulates and transmits 8 E1 TDM streams over IP/Ethernet networks; supports Web GUI and Console CLI network management
Port Configuration 8 × E1 ports, 2 × 10/100/1000M Ethernet RJ45 ports, 1 × 100/1000M SFP optical port, 1 × Web GUI interface, 1 × Console CLI interface
Power Input & Consumption Power Supply Options: AC 180V–260V / DC -48V / DC +24V  |  Power Consumption: ≤ 10W
Dimensions 485 mm × 135 mm × 44.5 mm (W × D × H)
Weight 2.3 kg / pc

Application

8e1 tdm over ip converter application

Interested in this product? Submit your inquiry below for a prompt response.

Scroll to Top